Baso Y71 Manuel d'utilisateur télécharger pdf (Page 2)

2 Y71 Regulator Conversion Kits Installation Instructions

To install the Y71 conversion kit into the gas valve:

1. Shut off the gas supply at the main manual

shutoff valve.

2. Change the orifices of the main burner and the

pilot burner to those recommended by the

appliance manufacturer.

3. Remove the outlet pressure tap plug from the

valve or manifold down stream of the valve and

install a manometer.

4. Remove Seal Screw A, Adjustment Screw B, and

Regulator Spring C from the regulator stack

(Figure 1).

IMPORTANT: Do not reuse the seal screw or

the regulator spring. However, the adjustment screw

may be reused. Note that the new seal screw and

regulator spring must be installed for proper

regulation.

5. Insert the new regulator spring, supplied in the

kit, into the regulator stack. Use care when

handling to avoid deforming the spring.

6. Reinstall the adjusting screw into the regulator

stack.

7. Turn on the gas supply and set the thermostat to

the highest setting.

8. Adjust the regulator to the manufacturer’s

specified setting by turning the adjusting screw in

the regulator stack. Turn clockwise to increase

and counterclockwise to decrease.

9. After the regulator adjustment is completed and

rechecked, install the new seal screw into the

regulator stack. Recheck setting.

10. Turn off the gas supply and set the thermostat to

Off or the lowest setting. Disconnect the

manometer and reinstall the pressure tap plug.

IMPORTANT: Place the adhesive-backed

Caution label on the visible side of the valve, making

sure the product label on the valve is not covered.

11. Using a felt-tipped pen, change the setting on the

label, located on the valve adjacent to the

regulator stack, to the new regulator setting

12. Turn on the gas supply and check for gas leaks

using a soap solution.

13. Perform the Checkout section before leaving the

installation.

Setup and Adjustments

Checkout

WARNING: Risk of Explosion or Fire.

Follow this or an equivalent checkout procedure

after installation. Before leaving the installation,

verify that the gas valve functions properly and that

the system has no gas leaks. Gas leaks can lead to

an explosion or fire, and may result in severe

personal injury or death.

Make sure all components are functioning properly by

performing the following test.

1. Open the main manual shutoff valve.

2. Test all joints and connections for leaks with a

soap solution.

3. Close the main manual shutoff valve and wait at

least 5 minutes for unburned gas to escape from

the appliance, and then reopen the shutoff valve.

4. Turn on the main electrical power switch and

close the thermostat contacts. The appliance

should operate in accordance with the

manufacturer’s specified sequence of operation.

5. Turn the thermostat to a low dial setting to open

the contacts. All burner flames should be

extinguished. Repeat Steps 3 and 4 at least three

times.

6. Return the thermostat to a normal setting before

leaving the installation.

Performance specifications are nominal and conform to acceptable industry standards. All agency certification of BASO products is performed

under dry and controlled indoor environmental conditions. Use of BASO products beyond these conditions is not recommended and may void

the warranty. Product must be protected if exposed to water (dripping, spraying, rain, etc.) or other harsh environments. The original

equipment manufacturer or end user is responsible for the correct application of BASO products. Consult BASO Gas Products LLC for

questionable applications. BASO Gas Products LLC shall not be liable for damages or product malfunctions resulting from misapplication or

misuse of its products.

Refer to the Y71/GM-70 Regulator Conversion Kits Product Bulletin (BASO-PB-Y71/GM) for necessary information on operating and

performance specifications for this product.

1007 South 12th Street

PO Box 170

Watertown, WI 53094 www.baso.com

1-877-227-6427 (1-877-BASOGAS) Published in U.S.A.

1 2

Commentaires sur ces manuels

Pas de commentaire

Baso Y71 Manuel d'utilisateur Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Baso Y71