Baso BGH2UNCNTRLHT-01 Manuel d'utilisateur télécharger pdf

Installation Instructions BGH

Issue Date October 4, 2010

Part No. BASO-INS-BGH, Rev. - www.baso.com

BGH2UNCNTRLHT-01 Universal

Hot Surface Ignition Control

Application

The BASO Gas Products BGH2UNCNTRLHT-01

Universal Series Hot Surface Ignition (HSI) control is

microprocessor based with timed ignition and suited

for replacement or new applications. Applications for

hot surface ignition modules include agricultural

equipment, space heaters, furnaces,

residential/commercial boilers, water heaters, pool

and spa heaters, and a variety of other commercial

cooking equipment.

This control includes a 5 position DIP switch allowing

up to 32 programmable pre-defined timing selections

to retrofit other Hot Surface Ignitions with flame

sensing rectification, such as: Johnson Controls,

Honeywell, White Rodgers, Fenwal, and

Robertshaw.

The BGH2UNCNTRLHT-01 works with single-rod or

dual-rod sensing to prove a flame. The control has a

continuous and precise monitoring of the HSI

element, wiring, and gas valve, shutting down in the

event of a failure. For a complete listing of

specifications, refer to the Technical Specifications

section.

Installation

IMPORTANT: Only qualified personnel

should install or service BASO Gas Products®.

These instructions are a guide for such personnel.

Carefully follow all instructions for the appliance.

IMPORTANT: Make all gas installations in

accordance with applicable local, national, and

regional regulations.

WARNING: Risk of Explosion or Fire.

Do not install the control in an area that is exposed

to water (for example, dripping, spraying, rain). Do

not use the control if it has been exposed to water.

Exposure to water may cause malfunction and can

lead to an explosion or fire and may result in

severe personal injury or death.

1 2 3 4 5 6 ... 18 19

Résumé du contenu

Page 1 - Hot Surface Ignition Control

Page 2

10 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions Checkout ! WARNING: Risk of Explosion or Fire. Verify that t

Page 3

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 11 • 100% Shutoff (Flame Not Sensed) With 3 Ignition Trials (

Page 4

12 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions NoYe sPower OnInitialize software,test ROM, RAM and E2get vol

Page 5

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 13 Troubleshooting! WARNING: Risk of Personal Injury. Do not

Page 6

14 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions YesNoNoYesTurn on powerand gas.Close thermostatcontacts.Modul

Page 7

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 15 Maintenance Requirements in Severe Environments Regular pre

Page 8

16 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions Cut out and leave near control. Green LED Indications During

Page 9 - Setup and Adjustments

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 17 Notes

Page 10 - Operation

18 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions Notes

Page 11 - Sequence of Operation

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 19 Technical Specification Product BGH2UNCNTRLHT-01 Universal

Page 12

2 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions Table 1: BGH2UNCNTRLHT-01 Universal Cross Reference Switch Po

Page 13 - Troubleshooting

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 3 Table 1: BGH2UNCNTRLHT-01 Universal Cross Reference Switch P

Page 14

4 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions Table 1: BGH2UNCNTRLHT-01 Universal Cross Reference Switch Pos

Page 15 - Repairs and Replacement

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 5 Table 1: BGH2UNCNTRLHT-01 Universal Cross Reference Switch P

Page 16

6 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions Replacing the Existing Ignition Control ! CAUTION: Risk of E

Page 17

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 7 GND(24V)GND(VALVE)GND(BURNER)HSIL1HSI24V(TH)VALVESENSE(REMOT

Page 18

8 BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions GND(24V)GND(VALVE)GND(BURNER)HSIL1HSI24V(TH)VALVESENSE(REMOTE)

Page 19 - Technical Specification

BGH2UNCTRLHT-01 Universal Hot Surface Ignition Control Installation Instructions 9 Setup and AdjustmentsSelect Dip Switch PositionsA 5 position

Commentaires sur ces manuels

Pas de commentaire

Baso BGH2UNCNTRLHT-01 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Baso BGH2UNCNTRLHT-01. BASO BGH2UNCNTRLHT-01 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Baso BGH2UNCNTRLHT-01