Baso BGA158 Series CE Approved Class B Manuel d'utilisateur télécharger pdf

Installation Instructions BGA158

Issue Date August 24, 2011

Part No. BASO-INS-BGA158CLASSB, Rev. C www.baso.com

BGA158 Series CE Approved Class B

Shutoff Gas Valve

Applications

The BGA158 Series shutoff gas valve is an electrically

operated shutoff valve that automatically open and

close on a demand signal from a thermostat or other

controlling device. Typical applications include

heaters, wall furnaces, commercial cooking

equipment, and similar applications. The BGA158 can

be used with natural gas and LP gas at pressures up

to 0.5 psi. Its compact size permits installation in

space restrictive applications.

Installation

IMPORTANT: Only qualified personnel should

install or service BASO® Gas Products. These

instructions are a guide for such personnel. Carefully

follow all instructions in this document and all

instructions for the appliance.

IMPORTANT: Make all gas installations in

accordance with applicable local, national, and

regional regulations.

CAUTION: Risk of Electric Shock.

Disconnect power supply before making electrical

connections to avoid electric shock.

WARNING: Risk of Explosion or Fire.

Shut off the gas supply at the main manual shutoff

valve before installing or servicing the BGA158.

Failure to shut off the gas supply can result in the

release of gas during installation or servicing, which

can lead to an explosion or fire, and may result in

severe personal injury or death.

WARNING: Risk of Explosion, Fire, or

Electric Shock. Label all wires before they are

disconnected when replacing or servicing the

BGA158. Wiring errors can cause improper or

dangerous operation and may result in an explosion,

fire, or electric shock leading to severe personal

injury or death.

IMPORTANT: Verify that the valve is installed

only in applications where the specified maximum

ambient (surface) temperature and maximum

operating pressure does not exceed the limits in the

Technical Specifications section.

To install the BGA158 valve:

1. Shut off power to the appliance.

2. Shut off the gas at the main manual shutoff valve.

3. Label each wire with the correct terminal

designation prior to disconnection.

4. Compare the voltage on the valve with the power

source voltage to ensure the correct unit is being

installed. For valves with 25-volt coils, use a

National Electrical Code (NEC), Class 2

transformer.

Note: The transformer must be mounted to a

grounded metal enclosure.

5. Ensure that the gas flows through the valve body

in the direction indicated by the “IN” and “OUT” on

the valve body. If the valve is installed with the gas

flow in the opposite direction, leakage can occur.

IMPORTANT: Do not use a wrench on any

surface other than the casting flats provided at the

inlet and outlet ends of the valve body. The BGA158

may be damaged in the mounting process if a wrench

is used on any other surface. Using a wrench

incorrectly may void the warranty.

1 2 3 4 5 6

Résumé du contenu

Page 1 - Shutoff Gas Valve

Page 2

2 BGA158 Series CE Approved Class B Shutoff Gas Valve Installation Instructions 6. The BGA158 valve may be mounted on a horizontal manifold with t

Page 3 - Setup and Adjustments

BGA158 Series CE Approved Class B Shutoff Gas Valve Installation Instructions 3 Wiring ! WARNING: Risk of Shock. Disconnect the power supply befor

Page 4 - L2 (Neu)

4 BGA158 Series CE Approved Class B Shutoff Gas Valve Installation Instructions Non-Polarity SensitiveConnectionsGround Tab25 VDC, 25V, 120V and 24

Page 5

BGA158 Series CE Approved Class B Shutoff Gas Valve Installation Instructions 5 Repairs and ReplacementTable 1: Replacement Solenoid Coil Part Numb

Page 6 - Technical Data

6 BGA158 Series CE Approved Class B Shutoff Gas Valve Installation Instructions Technical Data Product BGA158 Series CE Approved Class B Shutoff

Commentaires sur ces manuels

Pas de commentaire

Baso BGA158 Series CE Approved Class B Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Baso BGA158 Series CE Approved Class B. BASO BGA158 Series CE Approved Class B User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Baso BGA158 Series CE Approved Class B