Baso BGD258 Series BASOTROL CE Approved Class A Gas Val Manuel d'utilisateur télécharger pdf

Installation Instructions BGD258

Issue Date November 9, 2012

Part No. BASO-INS-BGD258, Rev. F www.baso.com

BGD258 Series BASOTROL®

CE Approved Class A Gas Valve

Installation

IMPORTANT: These instructions are intended as a

guide for qualified personnel installing or servicing

BASO Gas Products. Carefully follow all instructions

in this bulletin and all instructions on the appliance.

Limit repairs, adjustments, and servicing to the

operations listed in this bulletin or on the appliance.

WARNING: Risk of Fire or Explosion.

The system must meet all applicable local, national,

and regional regulations. Improper installation may

cause gas leaks, explosions, property damage, and

injuries.

WARNING: Risk of Fire or Explosion.

To prevent leakage of upstream gas, shut off the gas

supply at the main manual shutoff valve before

installing or servicing the BGD258 valve. Failure to

shut off the gas supply can result in the release of

gas during installation or servicing, which can lead to

an explosion or fire, and may result in severe

personal injury or death.

Mounting

CAUTION: Risk of Equipment Damage.

To prevent damage to the valve when mounting to

pipework, do not use a wrench on any surface other

than the casting flats provided at the inlet and outlet

ends of the valve body.

To install the BGD258 valve:

1. Ensure that the specified maximum ambient

(surface) temperature is not exceeded (see the

Technical Data section).

2. Ensure that the power supply voltage is

compatible with the required control valve voltage.

3. Shut off the gas at the main manual shutoff valve.

4. When installing the valve on the manifold, ensure

that the gas flows through the valve body in the

direction indicated by the arrow on the valve body.

If the valve is installed with the gas flow in the

opposite direction of the arrow, leakage can occur.

5. Mount the valve to the pipework. The BGD258

valve may be mounted on a horizontal manifold

with the solenoid coils pointed up (vertical) or in

any position not exceeding 90° from the vertical.

The valve also may be mounted on a vertical

manifold in any position around its axis (see

Figure 1). Do not install the solenoid coil upside

down. Install vertically wherever possible.

90° Maximum

from Vertical

90° Maximum

from Vertical

Limited Horizontal and Vertical

Vertical mounting may

be 360º around its axis

with the gas flow either

up or down, but always in

the direction of the arrow.

Regulator

Figure 1: BGD258 Valve Mounting Positions

1 2 3 4 5 6

Résumé du contenu

Page 1 - BGD258 Series BASOTROL®

Page 2 - Tap Connection

2 BASOTROL CE Approved Gas Valve Installation Instructions 6. Use an approved pipe joint sealing compound on the male threads before assembly. Re

Page 3 - Repairs and Replacement

BASOTROL CE Approved Gas Valve Installation Instructions 3 Wiring ! WARNING: Risk of Electrical Shock. Disconnect the power supply before making

Page 4

4 BASOTROL CE Approved Gas Valve Installation Instructions LNLNNon-Polarity SensitiveLine and NeutralConnectionsNon-Polarity SensitiveLine and Neu

Page 5 - Technical Specifications

BASOTROL CE Approved Gas Valve Installation Instructions 5 Technical Specifications Product BGD258 Series BASOTROL CE Approved Class A Gas Valve

Page 6

6 BASOTROL CE Approved Gas Valve Installation Instructions Technical Specifications (continued) Agency Listings CSA (AGA/CGA) Certificate Number

Commentaires sur ces manuels

Pas de commentaire

Baso BGD258 Series BASOTROL CE Approved Class A Gas Val Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Baso BGD258 Series BASOTROL CE Approved Class A Gas Val. BASO BGD258 Series BASOTROL CE Approved Class A Gas Valve User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Baso BGD258 Series BASOTROL CE Approved Class A Gas Val