Baso BGQ15HAA-1 Manuel d'utilisateur télécharger pdf

Installation Instructions

Issue Date November 3, 2011

Part No. BASO-INS-BGQ15, Rev. — www.baso.com

BGQ15HAA-1 Retrofit Spark Ignition System

Installation

Parts Included

The retrofit package includes:

• (1) BGD278JBE-20BCGD gas valve

• (1) BG1600M10EK-1AA spark ignition control

• (1) Rajah adapter

• (4) 1/4 inch female quick connects

• (1) Sensing probe cable

• (1) 1/8 inch NPT to 1/4 cc elbow fitting

• (1) Reducer bushing (3/4” to 1/2” NPT)

• (1) Compression fitting (1/4” tube)

• (1) Y75RJ-1 retrofit sensor probe kit

• (1) Sensor probe extension and (1) bushing

• (2) Spacers and (1) cone shaped nut

• retrofit package installation diagram and a

pressure sensitive lighting Caution sticker

Special Tools Needed

The following tools may be needed.

• manometer

• DC microammeter and AC voltmeter

• assorted pipe nipples and fittings

• On/Off toggle switch with wire leads and clips

Remove the Existing Gas Valve

IMPORTANT: Only qualified personnel should

install or service BASO Gas Products. These

instructions are a guide for such personnel. Carefully

follow all instructions in this document and all

instructions for the appliance.

IMPORTANT: Make all gas installations in

accordance with applicable local, national, and

regional regulations.

CAUTION: Risk of Electric Shock.

Disconnect power supply before making electrical

connections to avoid electric shock.

WARNING: Risk of Explosion or Fire.

Shut off the gas supply at the main manual shutoff

valve before installing or servicing the

BGQ15HAA-1. Failure to shut off the gas supply can

result in the release of gas during installation or

servicing, which can lead to an explosion or fire, and

may result in severe personal injury or death.

WARNING: Risk of Explosion, Fire, or

Electric Shock. Label all wires before they are

disconnected when replacing or servicing the

BGQ15HAA-1. Wiring errors can cause improper or

dangerous operation and may result in an explosion,

fire, or electric shock leading to severe personal

injury or death.

All installations must comply with local codes or, in the

absence of local codes, with the National Fuel Gas

Code, ANSI Z223.1, and the National Electrical Code

(NEC), ANSI/NFPA 70.

To remove the existing gas valve.

1. Set the thermostat at its lowest setting.

2. Turn off the power to the appliance.

3. Turn off the gas at the main manual shutoff valve.

4. Remove the thermocouple from the gas valve.

5. Disconnect the pilot tubing from the gas valve

Disconnect all wires from the existing gas valve.

6. Carefully remove the old gas valve from the

manifold.

1 2 3 4 5 6 ... 16 17

Résumé du contenu

Page 1 - Installation

Page 2 - Mounting

10 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions LED Error IndicationsIf the control module’s internal diagnostics detect a

Page 3

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 11 NoYesIdle StateCall for heatfrom the thermostatIf damper connectedwait fo

Page 4

12 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions YesNoNoYesTurn on powerand gas.Close thermostatcontacts.Module LEDdid not l

Page 5

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 13 NoYesContinuedfrom previous pagePilot is litMain burnerfailed to turnon?2

Page 6 - Setup and Adjustments

14 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions Maintenance Requirements in Severe Environments Regular preventive maintena

Page 7

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 15 Ignition Control Accessories Table 3: Ignition Control Accessories Part N

Page 8 - Operation

16 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions Technical Specification Product BG1600M10EK-1AA Intermittent Pilot Ignitio

Page 9 - Troubleshooting

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 17 Technical Specifications Product BGD278JBE-20BCGD Gas Valve Maximum Opera

Page 10

2 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions Install the Sensing Probe and Cable To install the sensing probe and cable:

Page 11

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 3 4. Mount the ignition system to the pipework. Use an approved pipe joint

Page 12

4 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions Wiring! WARNING: Risk of Explosion or Fire. Locate all safety, limit, and o

Page 13

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 5 1234Power Supply. Provides disconnect means and overload protection as req

Page 14 - Repairs and Replacement

6 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions Setup and Adjustments Electrical and Mechanical Checkout Procedure After the

Page 15 - Ignition Control Accessories

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 7 6. Ensure the thermostat contacts are open and remove the toggle switch.

Page 16 - Technical Specification

8 BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 5. Remove the seal screw at the end of the regulator stack. 6. Turn the ga

Page 17 - Technical Specifications

BGQ15HAA-1 Retrofit Spark Ignition System Installation Instructions 9 • Run: Main valve is energized and spark turns off after pilot flame is p

Commentaires sur ces manuels

Pas de commentaire

Baso BGQ15HAA-1 Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Matériel Baso BGQ15HAA-1. BASO BGQ15HAA-1 User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Matériel Baso BGQ15HAA-1